This configuration is used when high speed switches are not available.Ĭable your device as shown in the following diagram:Ĭonnect Port 1 on each node to a computer using an Ethernet crossover cable or a USB Ethernet adapter for the initial configuration of the device.Ĭonnect Port 2 on each node to a 1-GbE switch via a 1-GbE RJ-45 network cable. For more information on when to use these configurations, see Supported network topologies. The two-node device can be configured in the following different ways:Įach of these configurations is described in the following sections. Two, one, or no Graphical Processing Units (GPUs). The Wi-Fi antennas are installed on these connectors. Two Wi-Fi Sub miniature version A (SMA) connectors located on the faceplate of PCIe card slot located below Port 3 and Port 4. Mellanox dual port 100 GbE ConnectX-6 Dx network adapter - Port 3, Port 4.Intel Ethernet X722 network adapter - Port 1, Port 2.

One network card corresponding to two high-speed ports and two built-in 10/1-GbE ports: Two 100-Gbps interfaces, Port 3 and Port 4.

Two 10/1-Gbps interfaces, Port 1 and Port 2.

Has 2, 4, or 6 data disks in the 6 available slots depending on the specific hardware configuration.

Has six disk slots in the front of your device.

The front panel has disk drives and a power button. The Azure Stack Edge Pro 2 device should be connected to the datacenter network so that it can ingest data from data source servers.

Tighten the M5 screws of the chassis to the rail once the server is seated (reference diagram 5).

Once you hit a stop, pull and push the blue release tab on the inner rails (reference diagram 4).

Insert the chassis into the middle rail (reference diagram 3).

Ensure the ball bearing retainer is located at the front of the middle rail (reference diagrams 1 and 2).

Pull the middle rail so that it is fully extended in lock position.

Insert the chassis to complete the installation. Ensure the latch is fully engaged with the rack post. Make sure to fasten the inner rail screw.įix the outer rail and the bracket assembly to the frame. Locate the components for installing the rail kit assembly: Make sure that these are included in your rail kit.

Begin installing the rails in the allotted space that is closest to the bottom of the rack enclosure.

Before you begin, make sure to read the Safety instructions for your device.

If you decide not to mount your device, you can also place it on a desk or a shelf. For other mounting accessories, see Racking using a 2-post rackmount or Mounting the device on the wall. If you have received 4-post rackmount, use the following procedure to rack mount your device.

The device can be mounted using one of the following mounting accessory: The next step is to mount your device on a rack or wall. If you didn't receive all of the items listed here, Contact Microsoft Support. A wall mount (may be packaged separately).Ī safety, environmental, and regulatory information booklet.One packaged mounting accessory which could be: The accessory box includes Wi-Fi antennas, but Wi-Fi capability is not supported for the Azure Stack Edge device. Make sure that the minimum Internet bandwidth is 20 Mbps for optimal functioning of the device. For more information, see Azure Stack Edge Pro 2 networking requirements. Review the networking requirements for deploying Azure Stack Edge Pro 2, and configure the datacenter network per the requirements. If you wish to wall mount your device, you should have a space identified on the wall or a desk where you intend to mount the device. Standard AC power from an independent source.Ī power distribution unit (PDU) with an uninterruptible power supply (UPS).Īn available 2U slot on the rack on which you intend to mount the device. Verify that the site where you intend to set up has:.Make sure that the device rests safely on a flat, stable, and level work surface.You've generated the activation key to activate your device with the Azure Stack Edge resource.įor the Azure Stack Edge Pro 2 physical device.You've created an Azure Stack Edge resource to deploy your device.You've completed all the steps in Prepare to deploy Azure Stack Edge Pro 2.The prerequisites for installing a physical device as follows: For the Azure Stack Edge resource

Unpack switch